L. S. L. Elements. (C) Carbon, max. (Mn) Manganese, max. Amardeep Steel Centre is one of the leader manufacturers, Supplier and exporters of high quality ASTM A Stainless Steel Rectangular Tube, ASTM A Global Steel is one of the leading manufacturers, Supplier and exporters of High Quality ASTM A Steel Pipes, ASTM A Polished Stainless Steel Pipes.
|Published (Last):||2 April 2014|
|PDF File Size:||17.11 Mb|
|ePub File Size:||13.13 Mb|
|Price:||Free* [*Free Regsitration Required]|
Material meeting the requirements of S, S, or S may, by agreement between purchaser and manufacturer, be certified as S Click here For more ss material price list.
Unless otherwise specified in the ordering information, an order specifying S or Typeshall be satisfied by any one of S, S, or S at the option of the seller. Ratio of Wall Thickness to Outside Diameter. A polished stainless steel ornamental tubes are widely used for building constructions and architectural applications.
Nominal Pipe Size Inches. Tied with steel trips, then wrapped by asttm material. 5a54 values given in parentheses are mathematical conversions to SI units that are provided for information only and are not considered standard. It is informational only and not an official part of the standard; the full text of the standard itself must be referred to for its use and application.
ASTM does not give any warranty express or implied or make any representation that the contents of this abstract are accurate, complete or up to date. Radii of Corners, max. B For ovality values, the tolerance for average outside diameter at any one cross section does not exceed the outside diameter tolerance value for the applicable outside diameter.
Elongation in 2 in.
ASTM A554 Welded Tubing Standard(English)
Heat analysis shall be performed wherein several grades of steel shall conform to the required adtm composition for carbon, manganese, phosphorus, a5554, silicon, nickel, chromium, molybdenum, titanium, columbium, and tantalum.
Ovality is the difference between maximum and minimum outside diameters measured at any one cross section. Material meeting the requirements of S, S, or S may, by agreement between purchaser and manufacturer, be certified as S Unless otherwise specified in the ordering information, an order specifying S or Typeshall be satisfied by any one of S, S, aa554 S at the option of the seller. For square or rectangular structural tubing with heavier walls, the radius of any outside corner of the section shall not exceed three times the specified wall thickness.
Tensile Strength, min ksi MPa. Small outside diameter tubes are defined as those less than 0. The average of maximum and minimum outside diameter readings should fall within the outside diameter tolerances as shown in this table.
Twist In 3 ft. E These tolerances apply to cut lengths up to and including 24 feet. The values given in parentheses are mathematical conversions to SI units that are provided for information only and are not considered standard.
Tubes shall be furnished in one of the following shapes – round, square, rectangular, or special.
ASTM A Polished Stainless Steel Pipes, ASTM A SS Pipes, ASTM A Polished Pipes
Up to 6 meters, custom cut lengths Thickness: Tolerances Hot Finished Round Table. For sized over 5-in. Small outside diameter tubes are defined as those less than 0. Permissible Variations in Cut Length in. A Grade Tube. Tolerances — Diameter, Wall— Round Tubing. This abstract is a brief summary of the referenced standard. Also see Footnote B. This guide covers standard specification for welded stainless steel tubing for mechanical applications where appearance, mechanical properties, or corrosion resistance is needed.
Specified Size, Outside Diameter, In. Therefore, the wall thickness can vary 15 percent over and under that specified, and the inside diameter is governed by both the outside diameter and wall thickness tolerances.
ASTM A554 Stainless Steel Rectangular Tube
For sizes up to and including 5-in. We can offer polished stainless steel pipes in NO. Referenced Documents purchase separately The documents listed below are referenced within the subject standard but are not provided as part of the standard. Where ellipses … appear in this table, there is no minimum and analysis for the element need not be determined or reported. Yield Strength min, ksi MPa.
Bright Annealed, Polished Trade Name: Largest Specified Outside Dimension, Inches. A welded stainless steel tubing for mechanical applications where appearance, mechanical properties, or corrosion resistance is needed in a number of standard sizes and grades.
Link to Active This link will always route to the current Active version of the standard. A These tolerances apply to cut lengths up to and including 24 feet.
The tubes shall be made from flat-rolled steel by an automatic welding process without the addition of filler metal. The straightness tolerance is 0. The grades covered are listed in Table 1. A Grade L Tube.
Historical Version s – view previous versions of standard.