ASTM D(). Standard Guide for Testing Coating Powders and Powder Coatings. standard by ASTM International, 06/01/ View all product . Purchase your copy of ASTM D – 06() as a PDF download or hard copy directly from the official BSI Shop. All BSI British Standards. Mitsubishi GT06 Autotitrator. P-E Headspace .. Coating. Provider. From ASTM. D 5 Samples from powder coating lot to be used. 5.
|Published (Last):||24 September 2008|
|PDF File Size:||5.12 Mb|
|ePub File Size:||15.15 Mb|
|Price:||Free* [*Free Regsitration Required]|
Add to Alert PDF. Rather than discover these problems on the production coating line, it is recommended that the compatibility of powders be checked prior to their use. NOK 1 ,00 excl. Interpretation of the test results will depend on the speci?
No other units of measurement are included in this standard. Abrasion resistance Air blast abrasion tester Falling sand method Taber abraser Adhesion Tape adhesion Chemical resistance Household chemical resistance Detergent resistance Acid resistance Stains or reagents on wood substrates Chip resistance Gravelmeter Edge coverage Electrical insulation Elongation?
This is true whether the test is an established test, like salt spray Practice Bor a new test developed to simulate an environmental service condition unique to one given industry. Do not use abrasives to clean the bar. The physical stability of a thermoplastic coating powder can also be predicted.
Impact resistance has also been found to be a good indication of whether a coating powder has been adequately cured. Color pigmented coatings Visual Instrumental You can download and open this file to your own computer but DRM prevents opening this file on another computer, including a networked server.
Standards Subscriptions from ANSI provides a money-saving, multi-user solution for accessing standards. Historical Version s – view previous versions of standard. However, at unrealistically high irradiance levels, high amounts of near infrared energy can cause unrealistic temperature differences in differently colored materials.
No other units of measurement are included in this standard. The spectrum of this device compared more favorably to sunlight than the enclosed carbon-arc.
ASTM International – Standard References for ASTM D – 06()
Usage of paint asgm is so varied that no one set of conditions length or place of exposure can be given in this guide to cover all situations. The rate and type of degradation produced in exposure to enclosed carbon-arc can be much different from that produced in exposure to the outdoor environment or other types of laboratory light sources.
Last previous edition D — As the voice of the U. Adhesion tests can also be used for testing the degree of attachment between a primer powder coating or other coating type and a second coat of coating powder that is, intercoat adhesion.
You asgm delete a document from your Alert Profile at any time. For the reported 3d451-06 power to be signi?
The xenon arc source decays as the d34511-06 ages, but it can be controlled by adjusting the lamp wattage. The moment new editions of the standards you monitor are released, changes are made, or appendixes are published, you will be alerted by email. Your Alert Profile lists the documents that will be monitored.
The results are most meaningful when a control powder, one whose? Selection of the methods to be followed must be governed d3541-06 experience and the requirements in each individual case, together with agreement between the purchaser and the seller. A spectrophotometer, the preferred instrument, measures re? Allow 60 min for the warm up on the heating bar.
It should be noted that many of the methods used for characterizing a atm powder, such as wstm time Section 16 and inclined flow Section 17are primarily meant for the relative comparison of two coating powders, rather than to give a test value that can be interpreted as good or bad. Place the pointer between these two divisions.
Spectrophotometers offer a choice of two standard observers, speci? For example, the appliance industry has developed accelerated tests to simulate the long term service exposure of range stove components to heat cycles or food soils, or both. A second method uses a portable instrument that when scanned across the surface acts like the human eye and detects differences in re?
It can also show whether there is any change in? Please first log in with a verified email before subscribing to alerts. For thermoplastic materials, no chemical reaction takes place.
These conditions may be indicated by the individual test procedure used or agreed upon between the purchaser and seller. There are many types of abrasion tests available and often one, more than the others, will best simulate the abrasion resistance required in a particular end use application.
It is applicable to both thermoplastic and thermoset coatings, unless indicated otherwise. Impact resistance is dependent on the substrate type and its preparation, the thickness of the substrate, and the?
Therefore, these test parameters should be agreed upon between the purchaser and the seller. This ensures that you are always up-to-date and saves you both time and money. Where more than one test method is listed for the same characteristic, no attempt is made to indicate superiority of one method over another.
A deviation from the standard bake must be agreed upon between the d34551-06 and seller.
Standards Subscriptions from ANSI provides a money-saving, multi-user solution for accessing standards. Many properties of powder coating? Brush the material towards the lower temperature and note the location where particles of powder adhere to the bar when brushed lightly. There is no consistent correlation between the two tests. If the document is revised or d33451-06, you will be notified by email.
The following test method indicated has been found suitable d345106 this purpose. If the document is revised or amended, you will be notified by email. Start Webshop Product catalog Product presentation. By design this c3451-06 does not purport to address test methods or procedures developed specifically for the functional powder coating market, those coating powders for application to pipe or reinforced steel bars rebar.
Flow will re-occur if re-heated.