DLR datasheet, DLR datasheets and manuals electornic semiconductor part. FSDLRL, FSDLRL, FSDLRL, FSDLRL and other. Datasheet search engine for Electronic Components and Semiconductors. DLR data sheet, alldatasheet, free, databook. DLR parts, chips, ic. DLR datasheet,Page:3, FSDLRN Pin Definitions Pin Number 1 Pin Name GND Pin Function Description Sense FET source terminal on primary side .
|Published (Last):||16 July 2013|
|PDF File Size:||15.33 Mb|
|ePub File Size:||4.4 Mb|
|Price:||Free* [*Free Regsitration Required]|
The Sense FET and the con. It datashet a 0. The Drain datashest is designed to connect directly to the primary lead of the trans- former and is capable of switching a maximum of V. Maximum practical continuous power in an open frame. Then, Vfb climbs up in a similar manner to the over load situation, forc- ing the preset maximum current to be supplied to the SMPS until the over load protection is activated.
Once the Vcc reaches. In order to prevent this situation, an over voltage protection OVP circuit is employed.
This device is an integrated. Frequency Change With Temperature 2. There is a time delay while charging between 3V and 6V using an internal 5uA current source, which prevents false triggering under transient conditions but still allows the protection mechanism to operate under true dl0165g conditions. It also datashete to prevent transformer saturation and.
The voltage on the output capacitors is progressively increased with the intention of smoothly establishing the required output volt- age. Internal Soft Start Time. The typical soft start time is 15msec, as shown in figure 8, where progressive increments of Sense FET current are allowed during the start-up phase. Because excess energy is provided to the output, the output voltage may exceed the rated voltage before the over load protection is activated, resulting in the breakdown of the devices in dl0165e secondary side.
Here, pulse by pulse. Positive supply voltage input.
– ,+ datasheet pdf search and download
In order to prevent this situation, an over. Vcc instead of directly monitoring the output voltage. Although connected to an auxiliary transform- er winding, current is supplied from pin 5 Vstr via an internal switch during startup see Internal Block Diagram section. Pin Configuration Top View 3.
In order to avoid undes- ired activation of OVP during normal operation, Datashedt should be properly designed to be below 19V. Startup Voltage Vstr Breakdown.
If this pin is tied to Vcc or left floating, the typical current limit will be 1. In addition to start-up, soft- start is also activated at each restart attempt during auto- restart and when restarting after latch mode is activated.
(PDF) DL0165R Datasheet download
Drain to Source Peak Current Limit. Typical continuous power in a non-ven. Over load protection 4. It is not until Vcc reaches the UVLO upper datashet 12V that the internal start-up switch opens and de- vice dl065r is supplied via the auxiliary transformer winding.
If the sensing resistor voltage is greater. Delay current 5uA charges the Cfb. The voltage across the resistor is then compared with a. In order to avoid undes. When the gate turn-on. The pulse width to the power switching device is progres- sively increased to establish the correct working conditions for transformers, inductors, and capacitors.
This pin connects directly to the rectified AC line voltage source.
When compared to a discrete. The integrated PWM controller features include: Turn Off Delay Time.
The integrated PWM controller features. Pin to adjust the current limit of the Sense FET.
DLr datasheet & applicatoin notes – Datasheet Archive
This device is an integrated high voltage power switching regulator which combine an avalanche rugged Sense FET with a current mode PWM control block. A feedback voltage of 6V trig- gers over load protection OLP. There is dk0165r time delay while charging. UVLO upper threshold 12V that the internal start-up switch opens and de. This device is a basic.
Home – IC Supply – Link. Sense FET source terminal on primary side and internal control ground. Although connected to an auxiliary transform. In case of malfunc- tion in the secondary side feedback circuit, or feedback loop open caused by a defect of solder, the current through the opto-coupler transistor becomes almost zero.
In case of malfunc. T D OFF independent of. At start up the internal switch supplies internal bias and charges an external storage capacitor placed between the Vcc pin and ground.