JIS B 6402 PDF

Read 3 answers by scientists with 1 recommendation from their colleagues to the question asked by Daniel Martinez Krahmer on Dec 17, JIS B Mechanical power presses — Testing of the accuracy (FOREIGN STANDARD. Find the most up-to-date version of JIS B at Engineering

Author: Zulkigul Samulkis
Country: Kuwait
Language: English (Spanish)
Genre: Career
Published (Last): 18 August 2018
Pages: 144
PDF File Size: 16.35 Mb
ePub File Size: 4.37 Mb
ISBN: 815-3-49101-981-4
Downloads: 30078
Price: Free* [*Free Regsitration Required]
Uploader: Vokus

That means that there exists a risk that the machine is used under overload situation without knowing.

Since the screw press has no mechanical lower-dead-point, the machine never stops caused from overload stick like the crank press machine. Web Design City Dubai. Hydraulic Overload safety device. At the time of overload, 640 exceeding the rating capacity tonnage, the sensitive Hydraulic Overload Protection device senses the overload with a millisecond and immediately stops the machine.

Suitable centralized Motorised Lubrication Pump. The main frame plates are in one piece re-enforced by ribbing wherever necessary to provide rigidity to the frame and assuring least defection on full load. When you set up two strain gauges at each side of jjs frame, the load on one side frame equals to a half of jie load becomes setting value and shown as certain kN in RH and LH independently, plus total kN in the display. In case of the operation, hard-on-hard, in which striking die against die with the same condition as the above item?

Crank Shaft The Crank shaft would be of forged and normalized medium g steel to ensure toughness and shock resistance. The clutch is engaged through air pressure.

It is just a matter of revolution energy usage whether it is used for work piece compression or the frame deformation. Standard Equipments with each machine.

In other word, as the compression value for the testing piece is criterion, set the figures of equivalent amount on the load gauge. The screw press of kN; Set the load gauge that shows figures of when the testing work piece is compressed with the equivalent of kN. You may recognize from the above discussion that the load gauge display quite differs when smash up a test piece or strike die against die even if the forming energy is the same.

  6ED1 052-1MD00-0BA7 PDF

The machine is made operational by pushing the reset button. In the screw press, generally, the forming energy is adjusted with kis speed control just before stamping.

Emergency stopwatch would be provided in the control panel. Especially, in those large edge burrs and cold working, it could become out of the allowable load even if the forming energy value is still a half of it. Dual Sensing Solenoid valve. You can adjust the slide speed freely adjustable forming energy freelyhowever, you can’t control how n kN to strike. Set up the press slide speed and the slide stroke as maximum adjust to maximum power. Using the allowable capacity is disputable from the point of fair business transaction.

The load bb be placed on the center fundamentally. On the contrary, cold working stamping or stamping of steel plate with many edge burrs indicates large figures on the load gauge even if jia adjustment is relatively small.

It would be accurately machined and ground finished and so designed to ensure optimum factor of safety. Rotary 3 position Cam Limit Switch.

During work process like vertical compression of heated bar material, the energy is consumed for plastic deformation of the material mostly and the frame 6042 very small amount of load shown low value on the load gauge. We don’t use the torque limiter approach attached to the flywheel discharging overload energy. Naturally, if you form product under the same condition, the slide speed adjustment is proportional to the load gauge display.

It becomes quite expensive machine though we could manufacture it. This prevents any damage to the tool and to the press. As explained earlier, the press can compress a test piece with nominal capacity, however, it is absolutely impossible to do with the allowable capacity. If the preset value is small, the slide is clutched off right after acceleration and it descends evenly with inertia. There are always risks that the load surpasses the allowable load.

  BYGGNADERS SRDRAG PDF

Brake is automatically applied when the clutch is released.

Kaushico Machine Tools Pvt. Ltd.

Brake motor drives the worn shaft and wheel made of P. Attention is required that there is no relationship or relativity between the forming energy and the load display.

Even though frame is the same, larger amount of flywheel energy is put on to be a large performance press for hot forging and smaller amount of flywheel energy is put on to be a small performance press for cold forging.

Squirrel Cage Electric Motor. Two independent load display for each side simply shows one sided load and the total load is defined as screw press load. Our company does not employ this method because in case of hardened spring adjustment of the torque limiter by mistake, machine may always running with overload and finally machine may brake.

The frames are stress relieved before machining. Pneumatic balancer for slide 2 nos.

SPECIFICATIONS MODEL : ‘ESR’

This accurately machined steel jiis box type slide runs in extra long gibs fitted with PB liners, eliminating any possibility of tilting and maintains the parallelism of face even at off center loading.

Forming energy is completely same with flywheel energy. Its control is where the point to clutch off, not revolution control like inverter motor. The slide speed adjustment takes the method that controls to have same speed every jia based on encoder signal detected the slide descending speed.

It’s hardly recognizable to the operator if the torque limiter functions under the overload condition. Frame is stretched by three times This three time figure shows the maximum applied uis of the press. Machine life is drastically shortened if the press is used under three more times of nominal capacity maximum capacity repeatedly usually, the screw and the frame get damage.